Views: 0 Author: AMS titanium pipe supplier Ruiyang Publish Time: 2022-03-18 Origin: Titanium and Titanium Alloy Tubing supplier Ruiyang
AMS2244 AEROSPACE MATERIAL SPECIFICATION Tolerances (R) Titanium and Titanium Alloy Tubing
AMS4945 This specification covers a titanium alloy in the form of seamless tubing,the sizes tolerance follow the AMS2244 Tolerances,Titanium and Titanium Alloy Tubing
1.AMS2244 SCOPE: This specification covers established manufacturing tolerances applicable to titanium and titanium alloy tubing.These tolerances apply to all conditions, unless otherwise noted.The term "excl" is used to apply only to the higher figure of the specified range.
1.1 Tubing shall be specified in either inch/pound units or Sl units. When inch/pound units are used, the tolerances shown for SI units are not applicable.When Sl units are used, the tolerances for inch/pound units are not applicable.
2. DIAMETER:
When specified, OD tolerances shall apply to the ID but not to both ID and OD of the same lot of tubing.Mean OD is the average of two measurements taken at right angles to each other. Diameter tolerances include ovality except for tubing having specified wall thickness less than 4% of the specified OD; for tubing with specified wall thickness less than 4% of the specified OD,the ovality tolerance shall be double the diameter tolerance.
2.1 Seamless,Cold Reduced,Annealed or Stress Relieved:
Shall be as shown in Table 1.
TABLE 1A-OD Tolerances, Seamless Tubing, Inch/Pound Units
| ||
---|---|---|
Specified OD Inches | Standard Tolerance Inch Plus and minus | Special Tolerance Inch Plus only |
Up to 0.093,excl
| 0.002 |
0.002 |
0.093 to 0.100,excl
| 0.003 | 0.003 |
0.100 to 1.000,excl
|
0.004 | 0.004 |
1.000 to 1.500, excl
| 0.005 | 0.005 |
1.500 to 2.000,excl |
0.006 | 0.006 |
2.000 to 2.500,ecl | 0.007 | 0.007 |
2.500 to 3.500,excl | 0.010 | 0.010 |
3.500 to 4.500 excl | 0.015 | 0.015 |
TABLE 1B-
Tolerances, Seamless Tubing, SI Units
| ||
---|---|---|
Specifed OD,Millimeters | Standard Tolerance,Millimeter Plus and minus | Special Tolerance ,Millimeter Plus only |
Up to 2.50, excl | 0.05 | 0.05 |
2.50 to4.75,excl
| 0.08 |
0.08 |
4.75 to 25.00,excl | 0.10 | 0.10 |
25.00 to 37.50,excl
| 0.13 | 0.13 |
37.50 to 50.00,excl
| 0.15 | 0.15 |
50.00 to 63.50,excl
| 0.18 | 0.18 |
63.50 to 89.00,excl
| 0.25 | 0.25 |
89.00 to 115.00,excl
| 0.38 | 0.38 |
2.2 Welded,cold reduced,annealed or stress relieved:
Shall be as shown in table 2 or table 3 as applicable:
TABLE 2A- Standard OD
Tolerances, Inch/Pound Units | |
---|---|
Specified OD Inches
| Tolerances, Inch,plus only |
Up to 0.125, excl | 0.002 |
0.125 to 0.100, excl | 0.003 |
0.100 to 0.500, excl | 0.004 |
0.500 and over | 0.005 |
TABLE 2B-Standard OD Tolerances,SI Units | |
---|---|
Specified OD,Millimeters | Tolerance,Millimeter
,Plus only |
Up to 3.00,excl | 0.05 |
3.00 to 4.75,excl | 0.08 |
4.75 to 12.50,excl | 0.10 |
12.50 and over | 0.12
|
TABLE 3A-Special OD Tolerance,Inch/Pound Units | |
---|---|
Specified OD,Inches | Tolerance,Inch,plus only |
Up to 0.250, excl | 0.001 |
0.250 to 0.12,excl | 0.002 |
0.12 to 1.000, excl | 0.004 |
TABLE 3B-Special OD Tolerances,SI Units | |
---|---|
Specified OD Milimeters | Tolerance,Millimeter
,plus only |
Up to 6.25,excl | 0.03 |
6.25 to 20.50,excl | 0.05 |
20.50 to 25.00,excl
| 0.10 |
3.WALL THICKNESS: Shall not vary by more than ±10% for all sizes in both seamless and welded tubing, except that when special tolerances are specified,the variation shall be not greater than ±7.5%.
4. LENGTH: When tubing is ordered to specified lengths, tolerances on length shall be as shown in Table 4.
TABLE 4A- Length Tolerance, Inch/Pound Units
| |
---|---|
Specified Length,Feet
| Tolerance,Inch,plus only |
Up to 24.0, | 1/8 |
excl
24.0 to 34.0,excl | 1/4 |
34.0 to 44.0, excl | 3/8 |
44.0 to 65.0,excl | 1/2
|
TABLE 4B-Length Tolerance,SI Units | |
---|---|
Specified Length Meters | Tolerance,Millimeter,plus only |
Up to 7.3,excl | 3.2 |
7.3 to 10.4,excl | 6.4 |
10.4 to 13.4,excl | 9.5 |
13.4 to 19.8,excl | 12.7 |
5. STRAIGHTNESS: For tubing dimensioned in inch/pound units, tubes,4.500 inches and under in specified OD,shall be of such straightness that the maximum curvature (depth of arc) shall not exceed 0.025 inch in any one foot or 0.125 inch in any 5 feet of length.For tubing dimensioned in Sl units,tubes 115.00 mm and under in specified OD shall be of such straightness that the maximum curvature (depth of arc) shall not exceed 0.62 mm in any 300 mm or 4.15 mm in any 2 m of length.
Welcome contact us for seamless titanium tube and seamless titanium alloy pipes,also titanium weld tube for inquiry and order,we could supply you one stop service of titanium and titanium alloy pipes,not only meet AMS2244 aerospace material specifications.
petersy168
+86-18601515612